ASTM E1444-12 PDF DOWNLOAD
This standard is issued under the fixed designation E ; the number immediately following the designation indicates the 1 This practice is under the jurisdiction of ASTM Committee E-7 on Nonde- .. Hole numbers 8 thru 12 are optional. American Society for Testing Materials ASTM-E Utilising a Fixed Line Bench12 ASTM-E and where necessary harmonises the Standard with. Hello friends, who has ASTM E? I have the version 11, don’t know the change between the two version. Thanks.
|Published (Last):||6 September 2005|
|PDF File Size:||15.97 Mb|
|ePub File Size:||10.62 Mb|
|Price:||Free* [*Free Regsitration Required]|
Yes, it might be used on a daily basis and I have seen some procedures requiring it to be tested prior each test!!! It is the responsibility of the user of this standard to establish appropriate safety and health astm e1444-12 and determine the applicability of regulatory limitations prior to use.
Guide E144-412 astm e1444-12 be used in conjunction with this practice as a tutorial. Maximum detectability occurs when the discontinuity is positioned on the surface and perpendicular to the magnetic flux. It is not a detailed how-to procedure to be used by the examination personnel and, therefore, must be supplemented by a detailed written procedure that conforms to the requirements of this practice.
Now I can get involved with a new obsession! Link to Active This astm e1444-12 will always route to the current Active version f1444-12 the standard. See Astm e1444-12 X1 for additional information. Magnetic particle testing is not applicable to non-ferromagnetic metals and alloys such as austenitic stainless steels. Alternating current yokes shall have a lifting force of at least 10 lb 45 Nastm e1444-12 a 2 to 4-in. Magnetic particle testing is not applicable to non-ferromagnetic metals and alloys such as austenitic stainless steels.
The magnetizing power of all yokes shall be checked whenever the yoke has astm e1444-12 damaged or repaired. There are a total of 9 w1444-12 corrections in asym release.
I do not have the older versions of this standard at the moment so I do not know about the former requirements. Direct current yokes shall have a lifting force of at least 30 lb.
You can see the complete history of the standard at our usual revision history astm e1444-12 available for every standard on our website. astm e1444-12
I was able to find the 40lb lifting force in: The e1444-12 dimension of the plate or bar shall be astm e1444-12 than the pole spacing, s, of the electromagnet. Notes are optional and private. Magnetic particle testing may be applied to raw material, billets, finished and astm e1444-12 materials, welds, and in-service parts.
Alternating current and permanent magnet yokes shall have a lifting force of at least 10 lb [4. You can make atsm ASTM selection at our website, www. V article 7, para Astm e1444-12 And hasn’t changed ever since. If qstm yoke has not been in use for a year or more, a check shall be done prior to first use. The required verification intervals are stated in Table 1. Astm e1444-12 DC astm e1444-12 4 to 6 in.
I astm e1444-12 that I saw that somewhere. Lifting force according to ASME sec. Records of the verification results shall be maintained and retained for the time period specified in the contract.
The electromagnet astm e1444-12 a pole spacing, s, is placed on a steel plate as e14441-2 in Figure 1. The values stated in each system astm e1444-12 not be exact equivalents; therefore, each system shall be used independently of the other. Leave a Reply Cancel reply Your email address will not be published.
ASTM E/EM – Standard Practice for Magnetic Particle Testing | Engineering
Or you may prefer to contact us by phonefax or email info document-center. Combining values from the two systems may result in non-conformance with the standard. Establish a system in accordance with ANSI Z or ISO for calibration and astm e1444-12 of astm e1444-12 current and voltage astm e1444-12 devices, ammeter shunts, timers, lightmeters, gaussmeters, and field indicators used in verification.
Magnetic particle testing consists of magnetizing the area to be examined, applying suitably prepared magnetic astm e1444-12 while the area is magnetized, and subsequently interpreting and evaluating any resulting particle accumulations.
EB, Did you check what the Dead Sea scrolls had to say on the subject???? Equipment According axtm this standard: Yes it is used for Calibration and Certification.
New ASTM E/EM Edition – Magnetic Particle Testing – Document Center’s Standards Forum
This practice establishes the basic parameters for controlling the e1444-12 of the magnetic particle testing method.
E144-12 current yokes shall have a lifting force of at least 30 lb Nwith a 2 to 4-in. I wouldn’t hesitate if knew there astm e1444-12 something relevant inside those scrolls. The electromagnet shall be capable of supporting a steel astm e1444-12 or rectangular bar conforming to C22 1.
This practice is written so that it can be specified on the engineering drawing, specification, or contract. According to Table 3: There you can request delivery in paper or pdf format.
New ASTM E1444/E1444M 2012 Edition – Magnetic Particle Testing
Our expert staff can assist you with not only your standards purchases, but other management services to insure that asm collection is always up-to-date. Magnetization shall be determined by measuring the astm e1444-12 field strength, Ht, at the centre of a line joining the centres of the pole faces of the e1444–12 with pole extenders where used.
If astm e1444-12 still doesn’t get the answer to his question from the level of detail you provided astm e1444-12 I fear it would be hopeless to add more LOL Magnetic particle testing may be applied to raw material, billets, finished and semi-finished materials, welds, and astm e1444-12 parts. Referenced Asstm purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Related Products Searching for related products